How To Use Weather Seal Tape

Download Article

When it comes to keeping your business firm and car warm in the winter and cool in the summer, the cardinal is proper insulation. I style to help seal upward doors and windows in your house is to install agglutinative conditions stripping around the frames. Don't forget to screw on a sweep at the bottom of whatever outside doors to keep out hot or cold air, too. If you desire to insulate your motorcar, use adhesive to secure conditions stripping along the door jamb. Hello, energy efficiency!

1
Peel away any old weather stripping. Installing weatherstripping is a groovy way to embrace a window or door for winter. If your door or window currently has weather stripping, remove it before yous place the new piece downward. If the old stripping is adhesive, pull it off using your hands. If information technology's screwed into the frame, use a drill or screwdriver to take out the screws, then lift off the stripping.^[one]
- Try using a putty pocketknife to make it easier to peel abroad the old weather stripping. That will brand it easier to scrape away tape and whatsoever small pieces.^[2]
- If yous removed whatsoever screws, ready them bated and then you lot can use them on the new stripping.
2

Scrub off any sticky residue with an adhesive remover. If the leftover mucilage from the onetime stripping doesn't peel off easily, employ an adhesive remover with a cloth and scrub the area. Then dry it with a clean textile.

For extra stubborn adhesive that yous tin can't get off with the remover, sand information technology away with a fine-dust sandpaper. Look for a paper that is between 120 and 220-dust and run information technology over the residuum.

Advertisement
3
Clean the door or window jamb with soap and h2o, then dry it. This removes any remaining residue or droppings, which could touch on how well your new stripping sticks in place. With a cloth, wipe downwards the entire frame of the door or window with soap and warm water. Utilise another cloth to dry off the frame.^[iii]
- If there are whatever small holes or cracks in the frame, load a tube of exterior caulk into a caulk gun, and then pull the trigger to squeeze the paste into the hole. Let information technology dry out for about 24 hours before applying your stripping.
four
Measure the summit and side of your door or window frame. Hold i end of a record measure confronting the inside border of the frame, then stretch it to the other within edge to determine the length of the elevation and/or lesser slice of stripping. To measure the sides, place the end of the tape measure on the within edge of the top of the frame and pull the tape down to the floor.^[4]
- Measure twice to brand certain you lot have the almost authentic reading.
- It may help to have someone else read the measurement while you agree the tape in identify.
5
Select the type of adhesive weather stripping to use based on your door. The 3 most mutual types of agglutinative weather stripping are cream, Five strip, and prophylactic or vinyl. Agglutinative-backed foam tape is the well-nigh popular, as it's the easiest to install, simply if yous have a draftier door frame, you might adopt vinyl. Consider the specifics of your door or window when choosing your weather stripping.^[five]
- V strip may also be labeled as "tension seal."
- Y'all can find adhesive weather stripping at a hardware store or online retailer.
- Conditions stripping comes in unlike thicknesses, so it's a adept idea to buy a few different sizes, then try them out with your door. If the weather stripping you use is too thick, your door might not close properly.^[6]
- Purchase equally much weather stripping as yous demand based on your measurements, plus 10% extra as a precaution. For example, if you lot need 96 inches (240 cm) for your window, buy 106 inches (270 cm) of stripping.
How to Cull a Type of Weather condition Stripping

For the cheapest and easiest solution, get with foam tape. It costs less than $1 per 1 ft (0.30 m).

If you don't want to exist able to encounter the conditions stripping, choose Five strip. It's nearly invisible when installed correctly!

For sometime doors or windows that take big gaps, use prophylactic or vinyl weather stripping. The tubular pieces seal upward cracks ameliorate.
half dozen
Cut your pieces of weather stripping to the right length. Mark the length that you lot measured on the weather stripping using a pencil. Then trim the piece at the marked spot with a utility knife or pair of sturdy pair of scissors.^[seven]
- If y'all're weather stripping a window, you'll need iv pieces, ane for the top, 1 for the bottom, and i for each side.
- To weather condition strip a door, you need 1 piece for the top and 1 piece for each side, for a total of three strips. The lesser of the door will require a door sweep.
7
Line ane slice of stripping along the side of the door or window frame. Offset by placing the end of the atmospheric condition stripping in the height corner of the jamb. Then, arrange the residuum of the piece then it lies affluent confronting the door frame.^[8]
- Install the weather stripping when the exterior temperature is at least 50 °F (10 °C) to assist the adhesive hold improve.
- If you're using V strip, identify the stripping against the frame so that the opening of the V faces towards the exterior of the door or window.
- Practise not put the weather stripping on the door itself.
viii
Peel off the bankroll and press the stripping firmly into place. Once you have the stripping aligned where you want it to go, remove the paper backing from the piece. Run your hands along the piece and apply pressure to secure the pasty side of the stripping to the door or window jamb.^[9]
- To preclude the stripping from sticking to things it shouldn't, pare a little fleck of backing off at a time equally you become, instead of removing it all at once.
- For actress protection, you can secure the stripping into place by hammering nails through it into the frame, or use a staple gun to insert heavy-duty staples into it.
9
Echo on the other side and top of the frame. Install the remaining pieces around the door or window past removing the backing and pushing the adhesive against the jamb. Line up each piece in the corners and then that there are no gaps betwixt the pieces of stripping.^[10]
- If y'all're atmospheric condition stripping a window, make certain you apply a piece to the bottom edge, too.
x
Examination the door or window to make sure it opens and closes properly. Subsequently you've installed all of your stripping, effort opening and closing your door or window carefully. Check that it opens without sticking and that you can close it tightly.^[xi]
- Be aware that y'all may need to button or pull the window or door more firmly at get-go because of the new stripping.
- If you're having significant trouble opening or closing the window or door, conform your weather stripping as necessary.

1
Measure out the bottom of the door frame. Place one end of a tape measure on the inner edge of 1 side of the door frame. Pull the measure taut along the ground to the inner edge of the other side. Note what the measurement is. This is how long you'll need to cut the door sweep.^[12]
- Jot the measurement downwards on a piece of paper or type it in the notes app on your phone so you don't forget information technology.
2
Cut the metal door sweep to the right length with a hacksaw. Mark the length y'all measured on the door sweep with a pencil or marker. Clamp the sweep to a work table with the department you're going to cut hanging off the edge of the table. Apply force per unit area as you button the saw against the sweep and abroad from you. Repeat these pushing strokes until the saw cuts through the sweep.^[13]
- Ever vesture rubber glasses when cutting with a saw to protect your eyes from debris.
Tips for Cut with a Hacksaw

Choose the right blade. Make sure your hacksaw is fitted with a blade that works on metal, non one that'southward but for woods.

Push, don't pull. Hacksaws merely cut on the push stroke, so you don't need to pull it back through the sweep. Instead, you can elevator information technology up and bring it dorsum to the starting position.
3
Place the sweep at the bottom of the within of the door. Position it so that the flexible bottom piece of the sweep just grazes the floor. This will seal the gap underneath the door while likewise preventing the sweep from dragging against the flooring when you open and shut the door.^[14]
- You can check that your door sweep is aligned properly by looking underneath the door. If you tin see light coming through, move the sweep down a little until all of the low-cal is blocked.
4
Mark spots for the screws on the sweep and pre-drill pilot holes. Use a pencil to make a mark where each of the provided screws will go forth the door sweep, spacing out the pilot holes evenly in a directly line. For example, if you have 3 screws, brand one hole on each side of the sweep and and then 1 in the center. Line up the drill bit with the marks and pull the trigger to drill through both the sweep and the door itself.^[15]
- Your door sweep should come with three to 4 screws. If it doesn't, yous can use any #half-dozen screws.
- For #6 screws, use a drill chip that'southward at least ³⁄₃₂ inch (0.24 cm) in bore.
v
Use a screwdriver to insert the screws into the holes. Place i spiral in each of the holes and tighten them with a screwdriver until they're completely secure. This will secure the sweep to the door so it won't hang off or come loose.^[16]
- Test the door by opening and closing it a few times. If you observe the sweep is getting stuck, unscrew information technology from the door and adjust it equally needed.

1
Remove any old weather condition stripping that's already on the door. Utilize your easily to carefully peel off the piece that is currently on your car door. Make sure to pull upward what you can of the agglutinative layer underneath the stripping, as well.^[17]
- There may be screws in the stripping, which holds information technology in place. Unscrew them and set them bated.
- If you're having trouble peeling off the electric current slice, utilize adhesive remover to information technology and let information technology soften for fifteen to 20 minutes earlier trying again.
two
Utilize brake cleaner to clear out the channel, and so dry out it with a towel. This will get rid of whatsoever remaining agglutinative residue or clay in the aqueduct before yous identify the new stripping down. Hold the can most ii feet (0.61 m) from the door jamb and spray it forth the aqueduct. Wipe it off with a clean towel to remove whatever debris.^[18]
- If y'all have sensitive pare, vesture condom gloves when using restriction cleaner.
3
Utilize a thin line of weather condition stripping adhesive forth the channel. Less is more than when it comes to the adhesive. Clasp the tube to lay a bead of glue down the groove where you'll identify the weather stripping.^[19]
- Y'all can buy conditions stripping adhesive from an motorcar parts store or an online retailer.
4
Buy generic or custom weather stripping based on your preferences. While you can purchase generic weather stripping at any automobile parts store, y'all tin also get a piece that'south specifically designed to friction match your car'south make and model from the service section at your dealership. Custom stripping is more guaranteed to seal tightly effectually your machine doors.
- If yous aren't sure what to utilise, call your dealership or an auto technician and inquire their opinion.
- Custom weather stripping will be more expensive than generic stripping.
five
Place the new slice in the channel, pressing it firmly onto the adhesive. Line upwards the new weather stripping in the groove effectually the door. Push downwardly on the stripping once it'south aligned and then that the adhesive holds information technology in place.^[20]
- If you lot notice any spots where the agglutinative oozed out and hardened, use the brake cleaner to wipe them abroad
- If you had to remove any studs when yous peeled off the old weather condition stripping, screw those back into their proper places once you lot lay downwardly the new piece.
6
Let the adhesive dry for 45 minutes before closing the door. After the mucilage is completely dry, y'all can shut your car door. Notwithstanding, keep in heed information technology volition exist harder to close at first because of the new rubber.^[21]
- To make your new weather condition stripping concluding longer, you lot can spray it with a condom seal protectant after the adhesive has dried.
- You can also spray silicone on the weather stripping to prevent ice and snow from sticking to it in the wintertime.

Advertizing

Add New Question

Question

How do y'all replace the atmospheric condition stripping on an exterior door?

Jacob Pischer is a Home Improvement Specialist and the Owner of Helpful Badger, a home repair service in Portland, OR. With over four years of experience, Jacob specializes in a variety of handyman services including pressure level washing, cleaning gutters, repairing drywall, fixing leaky plumbing equipment, and repairing cleaved doors. Jacob studied at Madison Surface area Technical Higher and has a background in real estate investment.

Home Improvement Specialist

Expert Respond

Back up wikiHow by unlocking this adept answer.

Outset, use a putty knife to have all of the former weather condition stripping off the door. You desire to have a nice, clean surface for the adhesive. Then, installing the new stuff is uncomplicated—information technology'south usually simply double-sided mucilaginous tape on ane side, and you put it on the door jams.